Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - bpw

Pages: [1]
1
Gen 2 Montero / Re: Starter solenoid access
« on: August 28, 2019, 06:27:19 PM »
Back at the truck, ordered a whole starter.  Seemed worth it of I'm getting in there.

2
Gen 2 Montero / Starter solenoid access
« on: August 26, 2019, 10:02:44 AM »
I'm not near my Montero so can't check easily, but how easy is it to replace the starter solenoid vs. doing the entire starter?

I am getting occasional no start with a quiet click when I turn the key, then I turn the key a few times and all is good.  Thinking starter solenoid issue but if its just as much work to replace that as the whole starter I will put in a new starter, if the solenoid is easy I would rather do that first since starter looks like a hassle.  I am thinking the clicking I am hearing means its not the ignition switch, but could be wrong.  It sounds like some relay is engaging in the dash or hood, but much quieter than I would expect the main starter relay to be.  Only seems to happen on morning cold starts, no issue once the truck has been running a bit.  Battery is strong.

Thanks, I'm away from my truck for a few days and want to get parts ordered. 

3
For Sale Automotive / Re: WTS: 1998 Montero Gen 2.5 - Black Betty
« on: February 12, 2019, 08:27:02 PM »
Am I missing it or do you not have an asking price listed?

4
Gen 2 Montero / Re: New to Me 1994 Montero SR
« on: January 20, 2019, 12:23:29 PM »
When I put the locker in my truck I was able to splice a couple wires at the computer so I can now use the locker in 2wd but retained the other safety lock-outs that prevent engagement at speed etc.

Don't remember the wire colors anymore, but you just need to send power to the wire that senses the 4wd engagement.  Pretty sure it was ~5volt so I pulled the power from one of the other wires going onto the computer.

5
Gen 2 Montero / Re: ECU/TCU/check engine light
« on: January 02, 2019, 03:40:24 PM »
It may have just become moot, truck is 12 miles out a dirt road waiting to be dragged out friday after I had to leave it with a very loose crank pulley/harmonic balancer. 

Not sure the damage yet but I'm not real optimistic since the bolt felt messed up (could move freely 1/4 turn in either direction then jammed) and the pulley was moving around completely free with lots of wiggle.

Hoping the crank nose didn't get screwed up....but I'll start worrying about the check engine light once I confirm I don't need a new motor.

6
Gen 2 Montero / ECU/TCU/check engine light
« on: December 23, 2018, 01:56:20 PM »
Hi,

1998 Montero 3.5 CA emmisions, non-winter package but I have added a factory locker set-up and control module.

Somewhat odd set of issues and looking for thoughts on things to check as well as info on the TCU/ECU computers.

For the last couple months I have been chasing a check engine light showing code P0400 "EGR A flow" and P1750 Solenoid assembly.  The EGR code has been coming and going for few months while the solenoid error is recent.

My mechanic has gone through the EGR system and can't find any issue with EGR valves or vacuum leaks.  After a reset it often takes 500-1000 miles before it turns on again and it seems to correlate with a drop in the idle speed.

The Solenoid error code started showing after the truck would not shift into overdrive one day.  Restarting the car fixed the overdrive issue and it has not recurred but the code comes back after a reset.

Mechanic says he is not getting good info when he hooks his code reader up and suspects it may be an issue with a flaky ECU or TCU.

I also get a very occasional no start where the engine will not crank and turning the key off and on again fixes the problem, no solenoid click when it happens and starter is strong when it does work.  Most likely unrelated starter issues, but not sure if it could be the security system telling the car not to start.

This make any sense?  Any thoughts?

What years ECU and TCU cross reference?  They are pretty cheap used so I may just get them to try.

7
Gen 2 Montero / Re: Shift Kits
« on: October 14, 2018, 10:07:55 PM »
Thanks, very helpful.

8
Gen 2 Montero / Shift Kits
« on: October 13, 2018, 10:22:07 AM »
Am looking at getting a trans-go shift kit for my 1998 Montero, has anyone done and install and able to give an idea of how involved the process is?  Transgo doesn't seem to have installation instructions posted on the web anywhere.

9
For Sale Automotive / Re: US made HP Gen 2 radiators Group Buy
« on: August 20, 2018, 12:24:54 AM »
I have interest, more cooling never a bad thing.

10
Gen 2 Montero / Re: Rear gate handle broken
« on: August 19, 2018, 11:58:09 PM »
I just fixed my stuck door today, you can take off the interior panel with the door shut and access everything to get it freed up.

My issue was the lever that gets pushed by the handle was stuck so the door wouldn't unlock.  A bit of lube and all good.

Pages: [1]