Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - BottomFeeder

Pages: 1 2 [3]
31
Google Earth shows a really cool lot.  How many sofas do you think you can fit outside the house under the shade?

32
For Sale Automotive / Re: ISO: Gen 2 bouncy driver seat, manual
« on: July 11, 2017, 03:08:14 PM »
I have one for both sides of your rig

33
Mitsubishi Related / Re: ADD Complete Lift: Tips and Advice Gen 2
« on: June 04, 2017, 08:38:54 AM »
Thanks for the write up!  Maybe it can be stickeyed at the top?

34
General Discussion / Re: Show us your... trucks!
« on: May 27, 2017, 10:08:32 PM »
Tried all the URLS from my Flickr account.  None seem to work.

https://flic.kr/p/UD74rE

35
Mitsubishi Related / Re: 4.62 Ring Gear Q's
« on: May 27, 2017, 09:40:18 PM »
What are the trans gears for a 1990 LWB?

36
Mitsubishi Related / Re: 4.62 Ring Gear Q's
« on: May 23, 2017, 02:13:11 PM »
So, I guess the SR has lower transmission gears?

37
Mitsubishi Related / 4.62 Ring Gear Q's
« on: May 20, 2017, 03:23:27 PM »
95 SR on 33"s
4.62 gears
What RPM are you guys at 60 MPH?
I am at 2700

My 90 LS is just over 2k RPM with the same set up

38
General Discussion / Re: new member
« on: May 13, 2017, 07:31:55 AM »
I think we would all like to see some pics of your rig.

39
Mitsubishi Related / Re: Sport 4.90 Gears
« on: May 05, 2017, 10:13:56 PM »
Thanks

40
Mitsubishi Related / Re: Crankshaft Position Sensor Keeps Failing!
« on: April 14, 2017, 05:29:23 PM »
Would it be wise to run a new ground wire from the sensor harness above the intake manifold to a new ground location?

41
Mitsubishi Related / Sport 4.90 Gears
« on: April 14, 2017, 05:27:10 PM »
4.90 gears from a sport.  What years? 00-04? Looks like 3.5 and 3.0 were available in the sport of those years.  There are a couple in the local yards here in OKC.  Can I swap the ring and pinons fromthe sport to my 95SR?

42
Mitsubishi Related / Re: Crankshaft Position Sensor Keeps Failing!
« on: April 12, 2017, 02:11:25 PM »
That's the only thing left I can think of.  While testing the voltage we talked about that solution.  I guess it's time to dig in.

Thanks

43
General Discussion / Re: Who are you?
« on: April 08, 2017, 02:40:47 PM »
BottomFeeder on the Wire and Expo.  Richard Sauve on the Facebook

44
Mitsubishi Related / Crankshaft Position Sensor Keeps Failing!
« on: April 08, 2017, 02:38:57 PM »
I posted this over on the Expo AZ page.  Thought I'd see if I could get some help here as well.

Well, I need your help. My 95 SR is blowing through crank position sensors. I am now on the 5th sensor. All 3 wires have been tested and checked out with the right voltage. I have replaced the sensor ring (MD185237) and spacer (MD309036). I am on my 3rd mitsu crank sensor (MD303643) The 1st 2 were purchased at O'Reilly's and failed within minutes. As you all know, this process is like replacing the timing belt over and over and over and over again... Any advice and help is very much appreciated.

I am planing a trip to Colorado in June. I will also be heading to AZ at that time if I can get this sorted out.

Thanks

Pages: 1 2 [3]